|Model:||600W PCB SMD Board||Size:||180*180MM|
|CRI:||80||Aluminum Substrate Thickness:||2.0MM|
|Thermal Conductivity:||2.0W||Copper Foil:||35UM|
|Warranty:||3 Years Warranty||Spanlife:||50,000 Hours|
800w SMD 3030 LED PCB Board,
800W LED PCB Board,
SMD 3030 800W led bulb pcb board
Bridgelux 140-150LM/W High Power 400W 600W 800W PCB SMD Module With SMD 3030 Customizable for Tower Pendant Light
Related products Parameters
|The scope of products||Specification||Series-Parallel||Current /Voltage||Luminous Efficacy||Luminous Efficacy|
(Tower pendant lamp)
|300 WΦ110MM||25C12B||3600MA 75V||130-140LM/W||140-150LM/W|
|500 WΦ180MM||25C10B*2||3000MA 75V*2||130-140LM/W||140-150LM/W|
|600 WΦ180MM||25C12B*2||3600MA 75V*2||130-140LM/W||140-150LM/W|
|800 WΦ240MM||25C16B*2||4800MA 75V*2||130-140LM/W||140-150LM/W|
|1000 WΦ240MM||25C20B*2||6000MA 75V*2||130-140LM/W||140-150LM/W|
|1200 WΦ315MM||25C16B*3||4800MA 75V*3||130-140LM/W||140-150LM/W|
High Bay light/ Chandeliers/ Tower pendant lamp/ Flood light/ Street light
To avoid moisture, we recommend storage conditions for the unopened LED +5 ~ +30℃ rela-tive humidity <60%. LED should be used within 168 Hrs. of opening the package. Please make sure to dehumidify and vacuum pack the remaining/ unused LED. Dehumidifying condition:
+120℃±5℃ of 4Hrs. Effective age for the sealed led is one year.
The soldering precautions
Soldering conditions: Reflow soldering is not recommended for this LED. If hand soldering, set sol-dering iron temperature at 350℃ and soldering time not More than 5 seconds, after the first soldering, make sure the substrate surface temperature returns to ambient temperature before a second soldering. Please. make sure when soldering, there is no external force on the soldering surface and silicon batardeau (such as pressure, friction or sharp metal nails, etc.), to avoid gold wire deformation or dam-age and other abnormalities. If beyond recommended conditions, we cannot guarantee the LED stability, please do the risk assessment first. During assembly, please ensure that a good quality thermal paste is applied and distributed evenly over the surface. While using thermal pad (Heat Sink), make sure LED is firmly tightened and there is no gap between surfaces. In such heat-media products, through a pressure test of at least 500 volts.
Please take adequate measures to prevent electrostatic generation, such as wearing electrostatic ring or anti-static fingerstall etc; any relative products like plant equipment, machinery, carrier and transpor-tation units shall be connected to discharging unit/ ground. The ESD sensitivity of this product is > 1000V(HBM), after assembly the final lamp, please make sure to discharge Static Electricity by proper ESD equipment.
Recommended temperature conditions for enhanced product life: Be sure to TS point (negative pads) controlled below 85℃, COB recommendation colloid surface temperature control ≤150℃.
The drive control
Drive this product at constant current. Output current range specifications should be ac-cording to the operational and other conditions, as mentioned in data sheet. Before using a constant voltage source or altered specifications other than recommended, please consider risk factors.
Contact Person: Skye Lin