|
Product Details:
|
| Product Name: | 3535 Package 740-745nm SMD LED | Power: | 3W |
|---|---|---|---|
| Current: | 600mA | Voltage: | 2-2.2V |
| Wavelength: | 740-745NM | Luminous Flux: | 5-10LM |
| Viewing Angle: | 120 | Life Span: | 50000 Hours |
| Certificate: | CE ROHS LM-80 | Warranty: | 3 Years |
| Application: | Flower Gardening/ Indoor/Outdoor House Growth Light | Thermal Resistance Junction To Board: | 8 °C/W |
| High Light: | 3W Indoor Led Full Spectrum,745NM Indoor Led Full Spectrum,745NM Full Spectrum Cob Led Chip |
||
IR SMD LED 740-745NM 3535 Package 3W XPG-3 SMD LED Size For Indoor/Outdoor House Growth Light 3 Years Warranty
Specification
Product features
Plant Grow Light COB Chip:
1. ENERGY SAVING AND HIGH EFFICIENCY: you can buy lamp beads of different bands to assemble into plant lights of different wattage. It will speed up the growth for indoor plants with 3 times,it’s popular for greenhouse plants even in cold winter.
2. FULL SPECTRUM: 380-800nm wavelength full spectrum is suitable for all fruits, vegetables, hydroponic, flower,gardening,indoor plants at all stages.The wavelength of light can be fully absorbed.
3. WATERPROOF LED LIGHT CHIP: LED plant light bulb with this kind of chip is available even used for outdoor gardening in rainy days.
4. SAFE AND USER-FRIENDLY: 4000V thunder is resisted,it’s waterproof,anti-dropping,anti-explosion.Intelligent temperature system enables LED grow light work whether under high or cold temp.
5. GUARANTEE AND WARRANTY: 50000h service life,we are manufacturer and we will enable 3 years warranty , 50000Hours lifespan. Any questions,you can contact us freely,and we will be please to help you.
Application
Related products
User Manuel
1. Storage
To avoid moisture, we recommend storage conditions for the unopened LED +5 ~ +30℃
rela-tive humidity <60%. LED should be used within 168 Hrs. of opening the package. Please
make sure to dehumidify and vacuum pack the remaining/ unused LED. Dehumidifying condition:
+120℃±5℃ of 4Hrs. Effective age for the sealed led is one year.
2. Anti-static measures
Please take adequate measures to prevent electrostatic generation, such as wearing
electrostatic ring or anti-static fingerstall etc; any relative products like plant
equipment, machinery, carrier and transpor-tation units shall be connected to discharging
unit/ ground. The ESD sensitivity of this product is > 1000V(HBM), after assembly the final
lamp, please make sure to discharge Static Electricity by proper ESD equipment.
3. The soldering precautions
Soldering conditions: Reflow soldering is not recommended for this LED. If hand soldering,
set sol-dering iron temperature at 350℃ and soldering time not More than 5 seconds, after the
first soldering, make sure the substrate surface temperature returns to ambient temperature
before a second soldering. Please. make sure when soldering, there is no external force on the
soldering surface and silicon batardeau (such as pressure, friction or sharp metal nails, etc.),
to avoid gold wire deformation or dam-age and other abnormalities. If beyond recommended
conditions, we cannot guarantee the LED stability, please do the risk assessment first. During
assembly, please ensure that a good quality thermal paste is applied and distributed evenly over
the surface. While using thermal pad (Heat Sink), make sure LED is firmly tightened and there
is no gap between surfaces. In such heat-media products, through a pressure test of at least
500 volts.
4.The drive control
Drive this product at constant current. Output current range specifications should be
ac-cording to the operational and other conditions, as mentioned in data sheet. Before using
a constant voltage source or altered specifications other than recommended, please consider
risk factors.
5.Temperature control
Recommended temperature conditions for enhanced product life: Be sure to TS point (negative
pads) controlled below 85℃, COB recommendation colloid surface temperature control ≤150℃.
Product Description
Customers feedback
1.I normally don't write reports but I was surprised for good about this product. Unbelieved brightness. Consider using a dimmer to control the bright. For sure I will buy a few more for my home project.
2. These are much better when used as under cabinet lighting than the standard chip style. Especially with reflective countertops. It's much more uniform and clean looking in the reflection. I install many strips through my electrical business. These were very great.
3.My customer is so happy with this lighting. The leds are bright and dimmable and a great white shade., not blue or amber. Most importantly they are a solid light, no dots. Looks very high end. This is the only led strip lighting I will install from now on.
4.I have used a ton of other products from skye and this is by far my favorite. It looks awesome without all the individual diodes. I used a 24v transformer and made sure the wattage was rated higher that the 3w per ft I planned to use. These bend much tighter and are more flexible than other brands if used as well. I combine these with aluminum channels I buy from amazon to make them look like a fixture, including inside and outside corners.
Awesome light
5.Great tape lighting...such an upgrade from the "dotted" style. Would HIGHLY recommend this product for under cabinet, under counter, around mirrors in bathrooms, etc.
Contact Person: Skye Lin
Tel: 8613476793642
